Mechanical Parts

mechanical-parts

O Ring

o-ring

Silicone O-Rings are sometimes referred to VMQ O-Rings.

Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility. 

In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.

Overview on Application Rating for Material Silicone 

Heat Ozone & Aging Resistance - Excellent

Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.

O-Rings and rubber seals are generally used for:

· Applications that require resistance to OIL

· Applications that are required to work in low temperatures (-0°C)

· High performance Fuel systems that requires strictly no leakage

O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.

The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.

If you want to install an O-ring correctly and within a short time, here are steps to follow:

· Covering and lubricating the threading of the shaft

The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.

That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.

You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.

Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.

Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.

For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.

ORING JIS B2401 P31.5 ID 31.20 x CS 3.50Material : Silicone 70 Shore Silicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/~VjD15rUMKhKBjexLOWkFC.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P31.5&nbsp;
ID 31.20 x CS 3.50
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;&nbsp;&nbsp;
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:c4okr"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/~VjD15rUMKhKBjexLOWkFC.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="c4okr" 
 layout="nodisplay"></amp-image-lightbox>

ID - Yong Leng Trading ETH Account

KOYO

Others

Enerpac

Triangle

Optibelt

Nachi

Roller Bearing

Hydraulic Seals

Ball Bearings

Linear Bearing

Plain Bearings

Cam Follower Bearings

Other Tools

V Rings

buyerIntroduction

ORING JIS B2401 P31.5 ID 31.20 x CS 3.50 Silicone 70 Shore

oring jis b2401 p31.5 id 31.20 cs 3.50 silicone 70 shore silikon ring o-ring oem gelang oem/oem代工 3.50硅胶70肖氏 o型圈 oem代工

oring-jis-b2401-p31-5-id-31-20-x-cs-3-50-silicone-70-shore

ORING JIS B2401 P31.5 ID 31.20 x CS 3.50Material : Silicone 70 Shore Silicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/Bv2gec3rN32bL_Qtj4RsYJ.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P31.5&nbsp;
ID 31.20 x CS 3.50
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;&nbsp;&nbsp;
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:9jf75"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/Bv2gec3rN32bL_Qtj4RsYJ.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="9jf75" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P32 ID 31.70 x CS 3.50 Silicone 70 Shore

oring jis b2401 p32 id 31.70 cs 3.50 silicone 70 shore silikon ring o-ring oem gelang oem/oem代工 3.50硅胶70肖氏 o型圈 oem代工

oring-jis-b2401-p32-id-31-70-x-cs-3-50-silicone-70-shore

Nitrile is often referred to Buna (Buna-N) and NBR.

Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C). 

It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.

However Nitrile are not a restricting factors in many applications.

Overview on Application Rating for Material Nitrile (NBR) 

Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.

ORING JIS B2401 P31 ID 31.70 x CS 3.50Material : Nitrile (NBR) 70 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/fhEDDoMB74JMXFg3NpF59V.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P31 ID 31.70 x CS 3.50
Material : Nitrile (NBR) 70 Shore
&nbsp;&nbsp;&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:egp30"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/fhEDDoMB74JMXFg3NpF59V.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="egp30" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P31 ID 30.70 x CS 3.50 Nitrile (NBR) 70 Shore

oring jis b2401 p31 id 30.70 cs 3.50 nitrile (nbr) 70 shore ring o-ring oem gelang oem/oem代工 3.50腈（nbr）70肖氏 o型圈 oem代工

oring-jis-b2401-p31-id-30-70-x-cs-3-50-nitrile-nbr-70-shore

ORING JIS B2401 P31.5 ID 31.20 x CS 3.50Material : Nitrile (NBR) 70 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/eMknBXRcsrKfzlnhHBGRM0.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P31.5&nbsp;
ID 31.20 x CS 3.50
Material : Nitrile (NBR) 70 Shore
&nbsp;&nbsp;&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:9bjfr"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/eMknBXRcsrKfzlnhHBGRM0.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="9bjfr" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P31.5 ID 31.20 x CS 3.50 Nitrile (NBR) 70 Shore

oring jis b2401 p31.5 id 31.20 cs 3.50 nitrile (nbr) 70 shore ring o-ring oem pantai gelang oem/oem代工 3.50腈（nbr）70肖氏 o型圈 oem代工

oring-jis-b2401-p31-5-id-31-20-x-cs-3-50-nitrile-nbr-70-shore

ORING JIS B2401 P31 ID 30.70 x CS 3.50Material : Silicone 70 Shore Silicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/~Vvi~2FJi82vomnHPUzhV4.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P31
&nbsp;ID 30.70 x CS 3.50
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;&nbsp;&nbsp;
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:o7ng"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/~Vvi~2FJi82vomnHPUzhV4.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="o7ng" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P31 ID 30.70 x CS 3.50 Silicone 70 Shore

oring jis b2401 p31 id 30.70 cs 3.50 silicone 70 shore silikon ring o-ring oem gelang oem/oem代工 3.50硅胶70肖氏 o型圈 oem代工

oring-jis-b2401-p31-id-30-70-x-cs-3-50-silicone-70-shore

ORING JIS B2401 P32 ID 31.70 x CS 3.50Material : Nitrile (NBR) 70 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/4qD4Kdp1UPucsdt7jHqmOS.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P32&nbsp;
ID 31.70 x CS 3.50
Material : Nitrile (NBR) 70 Shore
&nbsp;&nbsp;&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:dbm6d"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/4qD4Kdp1UPucsdt7jHqmOS.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="dbm6d" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P32 ID 31.70 x CS 3.50 Nitrile (NBR) 70 Shore

oring jis b2401 p32 id 31.70 cs 3.50 nitrile (nbr) 70 shore ring o-ring oem gelang oem/oem代工 3.50腈（nbr）70肖氏 o型圈 oem代工

oring-jis-b2401-p32-id-31-70-x-cs-3-50-nitrile-nbr-70-shore

ORING JIS B2401 P32 ID 31.70 x CS 3.50Material : Nitrile (NBR) 90 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/Dlf4eLmfQuIM8T0_CdqQB7.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P32&nbsp;
ID 31.70 x CS 3.50
Material : Nitrile (NBR) 90 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:i30h"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/Dlf4eLmfQuIM8T0_CdqQB7.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="i30h" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P32 ID 31.70 x CS 3.50 Nitrile (NBR) 90 Shore

oring jis b2401 p32 id 31.70 cs 3.50 nitrile (nbr) 90 shore ring o-ring oem pantai gelang oem/oem代工 3.50腈（nbr）90肖氏 o型圈 oem代工

oring-jis-b2401-p32-id-31-70-x-cs-3-50-nitrile-nbr-90-shore

Material :  Viton Fluoroelastomers (FKM) 75 Shore   

Fluorocarbon O-Rings are usually call FKM or VITON elastomer, this elastomer are very close to being the universal material to be used in the sealing industry of O-Ring.

This is because due to it wideranges of chemical resistances and outstanding temperature combined with ozone, UV, weathering, and gasoline resistances. They have a temperature ranging from (-15`C to 199`C).

In addition fluorocarbon elastomer, have great benefit to be used in vacuum sealing due to its low gas impermeability ratings. 

The down side of fluorocarbon elastomer is, they should avoid being use in low temperature applications or exposing to hot water, steam, polar solvents, low molecular weight esters and esters, glycol based brake fluids or hot hydrofluoric or chlorosulfonic acids are a factor.

Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Fluorocarbon Viton O-Rings the standard nominal durometer is 75 Shore and 90 Shore.

ORING JIS B2401 P32 ID 31.70 x CS 3.50Material : Viton Fluoroelastomers (FKM) 75 Shore Fluorocarbon O-Rings are usually call FKM or VITON elastomer, this elastomer are very close to being the universal material to be used in the sealing industry of O-Ring.This is because due to it wideranges of chemical resistances and outstanding temperature combined with ozone, UV, weathering, and gasoline resistances. They have a temperature ranging from (-15&#x60;C to 199&#x60;C).In addition fluorocarbon elastomer, have great benefit to be used in vacuum sealing due to its low gas impermeability ratings. The down side of fluorocarbon elastomer is, they should avoid being use in low temperature applications or exposing to hot water, steam, polar solvents, low molecular weight esters and esters, glycol based brake fluids or hot hydrofluoric or chlorosulfonic acids are a factor.Temperature Range (Dry Heat)Low: -5&#x60;F / -15&#x60;C High: 390&#x60;F / 199&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - ExcellentTear Strength – GoodFuel Resistance - GoodHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - GoodAmmonia, Amines, Alkalis - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Fluorocarbon Viton O-Rings the standard nominal durometer is 75 Shore and 90 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/BezvHbSoGvLmc86bo69a6g.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P32&nbsp;
ID 31.70 x CS 3.50
Material : Viton Fluoroelastomers (FKM) 75 Shore&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;&nbsp;&nbsp;
Fluorocarbon O-Rings are usually call FKM or VITON elastomer, this elastomer are very close to being the universal material to be used in the sealing industry of O-Ring.
This is because due to it wideranges of chemical resistances and outstanding temperature combined with ozone, UV, weathering, and gasoline resistances. They have a temperature ranging from (-15`C to 199`C).
In addition fluorocarbon elastomer, have great benefit to be used in vacuum sealing due to its low gas impermeability ratings.&nbsp;
The down side of fluorocarbon elastomer is, they should avoid being use in low temperature applications or exposing to hot water, steam, polar solvents, low molecular weight esters and esters, glycol based brake fluids or hot hydrofluoric or chlorosulfonic acids are a factor.
<ins>Temperature Range (Dry Heat)</ins>
Low: -5`F / -15`C High: 390`F / 199`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Excellent
Tear Strength – Good
Fuel Resistance - Good
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Good
Ammonia, Amines, Alkalis - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Fluorocarbon Viton O-Rings the standard nominal durometer is 75 Shore and 90 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:fq4rf"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/BezvHbSoGvLmc86bo69a6g.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="fq4rf" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P32 ID 31.70 x CS 3.50 Viton Fluoroelastomers (FKM) 75 Shore

oring jis b2401 p32 id 31.70 cs 3.50 viton fluoroelastomers (fkm) 75 shore fluoroelastomer ring o-ring oem gelang oem/oem代工 3.50氟橡胶（fkm）75邵氏 o型圈 oem代工

oring-jis-b2401-p32-id-31-70-x-cs-3-50-viton-fluoroelastomers-fkm-75-shore

ORING JIS B2401 P31 ID 30.70 x CS 3.50Material : Nitrile (NBR) 90 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/dKpkZ0oFBTGrPVeB777hPl.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P31
&nbsp;ID 30.70 x CS 3.50
Material : Nitrile (NBR) 90 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:106qb"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/dKpkZ0oFBTGrPVeB777hPl.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="106qb" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P31 ID 30.70 x CS 3.50 Nitrile (NBR) 90 Shore

oring jis b2401 p31 id 30.70 cs 3.50 nitrile (nbr) 90 shore ring o-ring oem pantai gelang oem/oem代工 3.50腈（nbr）90肖氏 o型圈 oem代工

oring-jis-b2401-p31-id-30-70-x-cs-3-50-nitrile-nbr-90-shore

ORING JIS B2401 P35.5 ID 35.20 x CS 3.50Material : Silicone 70 Shore Silicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/y99zZ64OfUNIlzrPeULEB2.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P35.5&nbsp;
ID 35.20 x CS 3.50
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:39biq"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/y99zZ64OfUNIlzrPeULEB2.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="39biq" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P35.5 ID 35.20 x CS 3.50 Silicone 70 Shore

oring jis b2401 p35.5 id 35.20 cs 3.50 silicone 70 shore silikon ring o-ring oem gelang oem/oem代工 3.50硅胶70肖氏 o型圈 oem代工

oring-jis-b2401-p35-5-id-35-20-x-cs-3-50-silicone-70-shore

ORING JIS B2401 G105 ID 104.40 x CS 3.10Material : Silicone 70 Shore Silicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/DT1jYQI25cGavpTbE8qg_L.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 G105
&nbsp;ID 104.40 x CS 3.10
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:1sug4"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/DT1jYQI25cGavpTbE8qg_L.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="1sug4" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 G105 ID 104.40 x CS 3.10 Silicone 70 Shore

oring jis b2401 g105 id 104.40 cs 3.10 silicone 70 shore silikon ring o-ring oem gelang oem/oem代工 3.10硅胶70肖氏 o型圈 oem代工

oring-jis-b2401-g105-id-104-40-x-cs-3-10-silicone-70-shore

ORING JIS B2401 G405ID 404.30 x CS 5.70 Material : Silicone 70 Shore Silicone O-Rings are sometimes referred to VMQ O-Rings.Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59&#x60;C to 232&#x60;C) and it has good retention of compression and flexibility. In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.Temperature Range (Dry Heat)Low: -75&#x60;F / -59&#x60;C High: 450&#x60;F / 232&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - FairTear Strength – PoorFuel Resistance - PoorHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - ExcellentAbrasion Resistance - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/DGDhDX118HMfJk1jKpXZG1.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 G405
ID 404.30 x CS 5.70&nbsp;
Material : Silicone 70 Shore&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;&nbsp;&nbsp;
Silicone O-Rings are sometimes referred to VMQ O-Rings.
Silicone elastomers are an excellent material due to its outstanding resistance to extreme range of temperature ranging from (-59`C to 232`C) and it has good retention of compression and flexibility.&nbsp;
In addition Silicone perform excellent resistance to ozone, oxygen, moisture and water swell. Last of all, Silicone has and produces very low odour and taste elastomer therefore making it the right material to be used in food and beverage, and medical industry.
<ins>Temperature Range (Dry Heat)</ins>
Low: -75`F / -59`C High: 450`F / 232`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Fair
Tear Strength – Poor
Fuel Resistance - Poor
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Excellent
Abrasion Resistance - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance. Silicone O-Rings the standard nominal durometer is 70 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:6b0t4"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/DGDhDX118HMfJk1jKpXZG1.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="6b0t4" 
 layout="nodisplay"></amp-image-lightbox>

Oring Jis B2401 G405 Id 404.30 X Cs 5.70 Silicone 70 Shore

oring jis b2401 g405 id 404.30 cs 5.70 silicone 70 shore silikon ring o-ring oem gelang oem/oem代工 5.70硅胶70肖氏 o型圈 oem代工

oring-jis-b2401-g405-id-404-30-x-cs-5-70-silicone-70-shore

ORING JIS B2401 P31 ID 30.70 x CS 3.50Material : Viton Fluoroelastomers (FKM) 75 Shore Fluorocarbon O-Rings are usually call FKM or VITON elastomer, this elastomer are very close to being the universal material to be used in the sealing industry of O-Ring.This is because due to it wideranges of chemical resistances and outstanding temperature combined with ozone, UV, weathering, and gasoline resistances. They have a temperature ranging from (-15&#x60;C to 199&#x60;C).In addition fluorocarbon elastomer, have great benefit to be used in vacuum sealing due to its low gas impermeability ratings. The down side of fluorocarbon elastomer is, they should avoid being use in low temperature applications or exposing to hot water, steam, polar solvents, low molecular weight esters and esters, glycol based brake fluids or hot hydrofluoric or chlorosulfonic acids are a factor.Temperature Range (Dry Heat)Low: -5&#x60;F / -15&#x60;C High: 390&#x60;F / 199&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - ExcellentTear Strength – GoodFuel Resistance - GoodHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - GoodAmmonia, Amines, Alkalis - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Fluorocarbon Viton O-Rings the standard nominal durometer is 75 Shore and 90 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/Af~~2ni4O2DpZDFSusu~O8.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P31&nbsp;
ID 30.70 x CS 3.50
Material : Viton Fluoroelastomers (FKM) 75 Shore&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;&nbsp;
Fluorocarbon O-Rings are usually call FKM or VITON elastomer, this elastomer are very close to being the universal material to be used in the sealing industry of O-Ring.
This is because due to it wideranges of chemical resistances and outstanding temperature combined with ozone, UV, weathering, and gasoline resistances. They have a temperature ranging from (-15`C to 199`C).
In addition fluorocarbon elastomer, have great benefit to be used in vacuum sealing due to its low gas impermeability ratings.&nbsp;
The down side of fluorocarbon elastomer is, they should avoid being use in low temperature applications or exposing to hot water, steam, polar solvents, low molecular weight esters and esters, glycol based brake fluids or hot hydrofluoric or chlorosulfonic acids are a factor.
<ins>Temperature Range (Dry Heat)</ins>
Low: -5`F / -15`C High: 390`F / 199`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Excellent
Tear Strength – Good
Fuel Resistance - Good
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Good
Ammonia, Amines, Alkalis - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Fluorocarbon Viton O-Rings the standard nominal durometer is 75 Shore and 90 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:5ue59"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/Af~~2ni4O2DpZDFSusu~O8.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="5ue59" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P31 ID 30.70 x CS 3.50 Viton Fluoroelastomers (FKM) 75 Shore

oring jis b2401 p31 id 30.70 cs 3.50 viton fluoroelastomers (fkm) 75 shore fluoroelastomer ring o-ring oem gelang oem/oem代工 3.50氟橡胶（fkm）75邵氏 o型圈 oem代工

oring-jis-b2401-p31-id-30-70-x-cs-3-50-viton-fluoroelastomers-fkm-75-shore

ORING JIS B2401 P31 ID 30.70 x CS 3.50Material : Nitrile (NBR) 90 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/wIN2MIUvRUfcC~oysY5vhd.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P31
&nbsp;ID 30.70 x CS 3.50
Material : Nitrile (NBR) 90 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:clir9"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/wIN2MIUvRUfcC~oysY5vhd.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="clir9" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P31.5 ID 31.20 x CS 3.50 Nitrile (NBR) 90 Shore

oring jis b2401 p31.5 id 31.20 cs 3.50 nitrile (nbr) 90 shore ring o-ring oem pantai gelang oem/oem代工 3.50腈（nbr）90肖氏 o型圈 oem代工

oring-jis-b2401-p31-5-id-31-20-x-cs-3-50-nitrile-nbr-90-shore

ORING JIS B2401 P31 ID 30.70 x CS 3.50Material : Viton Fluoroelastomers (FKM) 75 Shore Fluorocarbon O-Rings are usually call FKM or VITON elastomer, this elastomer are very close to being the universal material to be used in the sealing industry of O-Ring.This is because due to it wideranges of chemical resistances and outstanding temperature combined with ozone, UV, weathering, and gasoline resistances. They have a temperature ranging from (-15&#x60;C to 199&#x60;C).In addition fluorocarbon elastomer, have great benefit to be used in vacuum sealing due to its low gas impermeability ratings. The down side of fluorocarbon elastomer is, they should avoid being use in low temperature applications or exposing to hot water, steam, polar solvents, low molecular weight esters and esters, glycol based brake fluids or hot hydrofluoric or chlorosulfonic acids are a factor.Temperature Range (Dry Heat)Low: -5&#x60;F / -15&#x60;C High: 390&#x60;F / 199&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - ExcellentTear Strength – GoodFuel Resistance - GoodHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - GoodAmmonia, Amines, Alkalis - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Fluorocarbon Viton O-Rings the standard nominal durometer is 75 Shore and 90 Shore.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/L3VHA~zkbPzJ1iE4oLm5U~.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P31&nbsp;
ID 30.70 x CS 3.50
Material : Viton Fluoroelastomers (FKM) 75 Shore&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;&nbsp;&nbsp;
Fluorocarbon O-Rings are usually call FKM or VITON elastomer, this elastomer are very close to being the universal material to be used in the sealing industry of O-Ring.
This is because due to it wideranges of chemical resistances and outstanding temperature combined with ozone, UV, weathering, and gasoline resistances. They have a temperature ranging from (-15`C to 199`C).
In addition fluorocarbon elastomer, have great benefit to be used in vacuum sealing due to its low gas impermeability ratings.&nbsp;
The down side of fluorocarbon elastomer is, they should avoid being use in low temperature applications or exposing to hot water, steam, polar solvents, low molecular weight esters and esters, glycol based brake fluids or hot hydrofluoric or chlorosulfonic acids are a factor.
<ins>Temperature Range (Dry Heat)</ins>
Low: -5`F / -15`C High: 390`F / 199`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Excellent
Tear Strength – Good
Fuel Resistance - Good
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Good
Ammonia, Amines, Alkalis - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Fluorocarbon Viton O-Rings the standard nominal durometer is 75 Shore and 90 Shore.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:ekckr"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/L3VHA~zkbPzJ1iE4oLm5U~.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="ekckr" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P31.5 ID 31.20 x CS 3.50 Viton Fluoroelastomers (FKM) 75 Shore

oring jis b2401 p31.5 id 31.20 cs 3.50 viton fluoroelastomers (fkm) 75 shore fluoroelastomer ring o-ring oem pantai gelang oem/oem代工 3.50氟橡胶（fkm）75肖氏 o型圈 oem代工

oring-jis-b2401-p31-5-id-31-20-x-cs-3-50-viton-fluoroelastomers-fkm-75-shore

ORING JIS B2401 G295 ID 294.30 x CS 5.70 Material : Nitrile (NBR) 90 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage<ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide

ORING JIS B2401 G295&nbsp;
ID 294.30 x CS 5.70&nbsp;
Material : Nitrile (NBR) 90 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage
<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

ORING JIS B2401 G295 ID 294.30 x CS 5.70 Nitrile (NBR) 90 Shore

oring jis b2401 g295 id 294.30 cs 5.70 nitrile (nbr) 90 shore ring o-ring oem pantai gelang oem/oem代工 5.70腈（nbr）90肖氏 o型圈 oem代工

oring-jis-b2401-g295-id-294-30-x-cs-5-70-nitrile-nbr-90-shore

ORING JIS B2401 P15 ID 14.80 x CS 2.40Material : Nitrile (NBR) 90 Shore Nitrile is often referred to Buna (Buna-N) and NBR.Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30&#x60;C to 100&#x60;C). It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.However Nitrile are not a restricting factors in many applications.Temperature RangeLow : -22&#x60;F / -30&#x60;C High: 212&#x60;F / 100&#x60;COverview on Application Rating for Material Nitrile (NBR) Properties ( Rating )Oils &amp; Grease - GoodTear Strength - GoodFuel Resistance - PoorGas impermeability - GoodCompression - ExcellentAbrasion Resistance - Good Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Primary UsageO-Rings and rubber seals are generally used for:· Applications that require resistance to OIL· Applications that are required to work in low temperatures (-0°C)· High performance Fuel systems that requires strictly no leakage <ul class="md-block-unordered-list-item"><li>Aircrafts</li><li>Marine Ships</li><li>F1 Cars</li></ul>· General Industrial Use Tips for installation of an O-ringO-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.So how do you install an O-ring?The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.If you want to install an O-ring correctly and within a short time, here are steps to follow:· Covering and lubricating the threading of the shaftThe threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.· Don’t force it over sharp cornersThat’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.· Even stretchingYou will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.· Don’t roll it down the shaftInstead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.· Finishing it offPlace the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.Installation Guide<figure class="md-block-image"><img src="https://storage.googleapis.com/eezee-product-images/eC34tytslwBkc71PxlG7tM.png" alt="" /><figcaption className="md-block-image-caption"></figcaption></figure>

ORING JIS B2401 P15&nbsp;
ID 14.80 x CS 2.40
Material : Nitrile (NBR) 90 Shore&nbsp;&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;
Nitrile is often referred to Buna (Buna-N) and NBR.
Nitrile elastomer being affordable is a common material widely used in the industry where sealing take place using O-Ring. It is popular in the industry due to it ability to withstand a wide range of temperature ranging from (-30`C to 100`C).&nbsp;
It has excellent resistance to petroleum application, it is rated good in the Gas impermeability. In addition Nitrile material are one of the best in its compression and abrasion resistance. The only down side of Nitrile have a poor ozone and weather resistance and only moderate resistance to high temperature.
However Nitrile are not a restricting factors in many applications.
<ins>Temperature Range</ins>
Low : -22`F / -30`C High: 212`F / 100`C
<ins>Overview on Application Rating for Material Nitrile (NBR) </ins>
Properties ( Rating )
Oils &amp; Grease - Good
Tear Strength - Good
Fuel Resistance - Poor
Gas impermeability - Good
Compression - Excellent
Abrasion Resistance - Good&nbsp;
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classify as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with Shore A scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.
<ins>Primary Usage</ins>
O-Rings and rubber seals are generally used for:
· Applications that require resistance to OIL
· Applications that are required to work in low temperatures (-0°C)
· High performance Fuel systems that requires strictly no leakage

<ul>
<li>Aircrafts</li>
<li>Marine Ships</li>
<li>F1 Cars</li>
</ul>
· General Industrial Use&nbsp;
<ins>Tips for installation of an O-ring</ins>
O-rings need to be installed properly for a perfect fit and sealing. It is important that you install the O-ring in a prescribed manner to ensure your application continues to function properly. You will also ensure you increase the life of the application.
<ins>So how do you install an O-ring?</ins>
The process of installing an O-ring into a male gland is an intricate affair that should be carefully undertaken. Glide it along the shaft so as it reaches the gland. At that point, it should easily snap into place. Simple as it might sound, a number of steps will ensure that the O-ring doesn’t get damaged.
If you want to install an O-ring correctly and within a short time, here are steps to follow:
· Covering and lubricating the threading of the shaft
The threading of the shaft has the potential of tearing the rubber seal. Cover the threads using a masking tape and then lubricate them to allow for easy passage of the O-ring. The aim is to have the O-ring slide through without getting torn.
· Don’t force it over sharp corners
That’s a tip that will save you the stress of a torn O-ring. In fact, running the O-ring over jagged or sharp objects could get it torn. You may not be able to notice some of these tears. That’s why you should ensure you prevent them from occurring in the first place.
· Even stretching
You will have to stretch the O-ring over the shaft. Ensure you do it evenly. Pulling from one side is a no-no. If anything, you should stretch the O-ring as little as possible. You will not just get a tighter grip but added security too.
· Don’t roll it down the shaft
Instead of rolling the O-ring down the shaft, slide it. If you spiral wind or roll an O-ring, it cannot be properly installed. It will also not function optimally and can even end up being damaged. If you have a lubricant, apply it on the O-ring and you will keep it rolling.
· Finishing it off
Place the female component in a manner that allows its radius to go around the corner. This should be done when you are finalizing the installation process. Ensure the lead of this component is inside the chamfer. This is how you will be able to guarantee the safety of the O-ring.
For O-rings to perform optimally, they have to be properly installed. It doesn’t just provide secure sealing but also increases the service life of the component together with the application. Don’t compromise on this process.
<ins>Installation Guide</ins>

 <div class="img-ctnr">
 <amp-img 
 on="tap:8ab80"
 tabindex="0"
 role="button"
 class="contain"
 layout="fill"
 src="https://storage.googleapis.com/eezee-product-images/eC34tytslwBkc71PxlG7tM.png"
 ></amp-img>
 </div>
 
 <amp-image-lightbox 
 id="8ab80" 
 layout="nodisplay"></amp-image-lightbox>

ORING JIS B2401 P15 ID 14.80 x CS 2.40 Nitrile (NBR) 90 Shore

oring jis b2401 p15 id 14.80 cs 2.40 nitrile (nbr) 90 shore ring o-ring oem pesisir gelang oem/oem代工 2.40腈（nbr）90肖氏 o型圈 oem代工

oring-jis-b2401-p15-id-14-80-x-cs-2-40-nitrile-nbr-90-shore

This is because due to it wide ranges of chemical resistances and outstanding temperature combined with ozone, UV, weathering, and gasoline resistances. They have a temperature ranging from (-15`C to 199`C).

O-Rings, rubber seals and custom molded rubber components for:

High temperature applications requiring good compression      set

Proper installation of an O-Ring will provide the perfect fit and sealing. The manner of installation is crucial to the functioning of the application. It also increases the longevity of the application.

When installing an O-ring into a male gland, the O-ring has to be glided along the shaft. Once it reaches the gland, it snaps in place. Although this process sounds extremely simple, some steps have to be taken to ensure that it does not tear or get damaged.

The following steps should help in installing an O-ring correctly and saving time as well:

1. The shaft consists of threading, which could tear the rubber seal. Covering and lubricating the threads will provide ease of passage. You can cover the threads using some masking tape.

2. You must avoid forcing the O-ring over sharp corners as well. Jagged or sharp features could tear the O-ring. These tears might sometimes not be noticeable. Thus, it is important to avoid it altogether.

3. When stretching the O-ring around the shaft, stretch it evenly. Do not pull from one side. Make sure that you stretch the O-ring as little as possible. This will provide a tighter grip and added security.

4. When installing an O-ring, do not roll it down the shaft. Instead, slide it down. A rolled or spiral wound O-ring cannot be properly installed, and will not function optimally and can result in damage. You can apply some lubricant to the O-ring as well to keep it from rolling.

5. When installing the rest of the assembly, it is important to place the female component in a way so that it has a radius around the corner. The lead of this component should be inside the chamfer. This process guarantees the safety of the O-ring.

Since O-rings are used to provide secure sealing when two parts are assembled, it is important that they perform optimally. For this purpose, proper installation is necessary. The installation process when performed correctly is capable of increasing the service life of the component as well as the application.

ORING JIS B2401 P60 ID 59.60 x CS 5.70Material : Viton Fluoroelastomers (FKM) 75 Shore Fluorocarbon O-Rings are usually call FKM or VITON elastomer, this elastomer are very close to being the universal material to be used in the sealing industry of O-Ring.This is because due to it wide ranges of chemical resistances and outstanding temperature combined with ozone, UV, weathering, and gasoline resistances. They have a temperature ranging from (-15&#x60;C to 199&#x60;C).In addition fluorocarbon elastomer, have great benefit to be used in vacuum sealing due to its low gas impermeability ratings. The down side of fluorocarbon elastomer is, they should avoid being use in low temperature applications or exposing to hot water, steam, polar solvents, low molecular weight esters and esters, glycol based brake fluids or hot hydrofluoric or chlorosulfonic acids are a factor.Temperature Range (Dry Heat)Low: -5&#x60;F / -15&#x60;C High: 390&#x60;F / 199&#x60;COverview on Application Rating for Material Silicone Properties (Rating)Oils &amp; Grease - ExcellentTear Strength – GoodFuel Resistance - GoodHeat Ozone &amp; Aging Resistance - ExcellentWater Swell Resistance - GoodAmmonia, Amines, Alkalis - PoorOther than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Fluorocarbon Viton O-Rings the standard nominal durometer is 75 Shore and 90 Shore.Primary UsageO-Rings, rubber seals and custom molded rubber components for: <ul class="md-block-unordered-list-item"><li>Automotive fuel handling</li><li>Aircraft engine seals</li><li>High temperature applications requiring good compression set</li><li>General industrial O-ring seals</li></ul>Important Tips When Installing an O-RingProper installation of an O-Ring will provide the perfect fit and sealing. The manner of installation is crucial to the functioning of the application. It also increases the longevity of the application.Installing an O-RingWhen installing an O-ring into a male gland, the O-ring has to be glided along the shaft. Once it reaches the gland, it snaps in place. Although this process sounds extremely simple, some steps have to be taken to ensure that it does not tear or get damaged.Tips for Better Installation of O-RingsThe following steps should help in installing an O-ring correctly and saving time as well:1. The shaft consists of threading, which could tear the rubber seal. Covering and lubricating the threads will provide ease of passage. You can cover the threads using some masking tape.2. You must avoid forcing the O-ring over sharp corners as well. Jagged or sharp features could tear the O-ring. These tears might sometimes not be noticeable. Thus, it is important to avoid it altogether.3. When stretching the O-ring around the shaft, stretch it evenly. Do not pull from one side. Make sure that you stretch the O-ring as little as possible. This will provide a tighter grip and added security.4. When installing an O-ring, do not roll it down the shaft. Instead, slide it down. A rolled or spiral wound O-ring cannot be properly installed, and will not function optimally and can result in damage. You can apply some lubricant to the O-ring as well to keep it from rolling.5. When installing the rest of the assembly, it is important to place the female component in a way so that it has a radius around the corner. The lead of this component should be inside the chamfer. This process guarantees the safety of the O-ring.Since O-rings are used to provide secure sealing when two parts are assembled, it is important that they perform optimally. For this purpose, proper installation is necessary. The installation process when performed correctly is capable of increasing the service life of the component as well as the application.

ORING JIS B2401 P60
&nbsp;ID 59.60 x CS 5.70
Material : Viton Fluoroelastomers (FKM) 75 Shore&nbsp;&nbsp;&nbsp;
&nbsp;&nbsp;
Fluorocarbon O-Rings are usually call FKM or VITON elastomer, this elastomer are very close to being the universal material to be used in the sealing industry of O-Ring.
This is because due to it wide ranges of chemical resistances and outstanding temperature combined with ozone, UV, weathering, and gasoline resistances. They have a temperature ranging from (-15`C to 199`C).
In addition fluorocarbon elastomer, have great benefit to be used in vacuum sealing due to its low gas impermeability ratings.&nbsp;
The down side of fluorocarbon elastomer is, they should avoid being use in low temperature applications or exposing to hot water, steam, polar solvents, low molecular weight esters and esters, glycol based brake fluids or hot hydrofluoric or chlorosulfonic acids are a factor.
<ins>Temperature Range (Dry Heat)</ins>
Low: -5`F / -15`C High: 390`F / 199`C
<ins>Overview on Application Rating for Material Silicone </ins>
Properties (Rating)
Oils &amp; Grease - Excellent
Tear Strength – Good
Fuel Resistance - Good
Heat Ozone &amp; Aging Resistance - Excellent
Water Swell Resistance - Good
Ammonia, Amines, Alkalis - Poor
Other than the size and material type, there is one final option that you need to take in consideration. And that is the Durometer. Durometer are being classified as an industry standard to measure the elastomer hardness. Durometer is measured and listed in accordance with “Shore A” scale. Typical standard hardness for the elastomer are 70 shore, 75 shore and 90 shore to choose from depending on the material that you are using. The higher the value of the shore indicates that the material you are using is harder.Durometer is also generally stated and accepted with a “+/- 5” tolerance.Fluorocarbon Viton O-Rings the standard nominal durometer is 75 Shore and 90 Shore.
<ins>Primary Usage</ins>
O-Rings, rubber seals and custom molded rubber components for:

<ul>
<li>Automotive fuel handling</li>
<li>Aircraft engine seals</li>
<li>High temperature applications requiring good compression set</li>
<li>General industrial O-ring seals</li>
</ul>
<ins>Important Tips When Installing an O-Ring</ins>
Proper installation of an O-Ring will provide the perfect fit and sealing. The manner of installation is crucial to the functioning of the application. It also increases the longevity of the application.
Installing an O-Ring
When installing an O-ring into a male gland, the O-ring has to be glided along the shaft. Once it reaches the gland, it snaps in place. Although this process sounds extremely simple, some steps have to be taken to ensure that it does not tear or get damaged.
Tips for Better Installation of O-Rings
The following steps should help in installing an O-ring correctly and saving time as well:
1. The shaft consists of threading, which could tear the rubber seal. Covering and lubricating the threads will provide ease of passage. You can cover the threads using some masking tape.
2. You must avoid forcing the O-ring over sharp corners as well. Jagged or sharp features could tear the O-ring. These tears might sometimes not be noticeable. Thus, it is important to avoid it altogether.
3. When stretching the O-ring around the shaft, stretch it evenly. Do not pull from one side. Make sure that you stretch the O-ring as little as possible. This will provide a tighter grip and added security.
4. When installing an O-ring, do not roll it down the shaft. Instead, slide it down. A rolled or spiral wound O-ring cannot be properly installed, and will not function optimally and can result in damage. You can apply some lubricant to the O-ring as well to keep it from rolling.
5. When installing the rest of the assembly, it is important to place the female component in a way so that it has a radius around the corner. The lead of this component should be inside the chamfer. This process guarantees the safety of the O-ring.
Since O-rings are used to provide secure sealing when two parts are assembled, it is important that they perform optimally. For this purpose, proper installation is necessary. The installation process when performed correctly is capable of increasing the service life of the component as well as the application.